When a firefighter passes, many, if not all of the time an apparatus (fire truck) is used as a caisson. Whether it’s an antique or a modern apparatus, it is a fitting way to transport a fallen brother or sister.
The hose bed is emptied and used to transport the casket. There are a couple problems, however. The first problem is the casket marring the hose bed floor and the second, more serious problem is the casket not being secure. Both problems are now solved.
Before we get to the solution, I want to briefly outline the process of loading/unloading a casket on an apparatus.
Assuming the removable casket deck is inserted into the hose bed, here is the process. The number of firefighters who handle the casket, besides the six or eight pallbearers, depends on the height and type of apparatus used.
In this picture, the firefighters who were in training with me had a real funeral for a retiree to attend during our academy in Texas (2013). You can see the men staged on the tailboard and hose bed to receive the casket from the pallbearers. All three men rode in the bed on the way to the church and cemetery ensuring the casket remained in place.
This is one of the pictures from the graduation ceremony later that same week. Here, the commander of the pallbearers, marches up, steps up onto the tailboard and ensures the casket is ready to move. He is executing an Air Force technique of dressing the flag before the pallbearers retrieve it. Notice the red metal step. This fire engine is an antique with a relatively high tailboard. I also know of portable platforms for pallbearers to step up onto that have room for all six pallbearers (I would appreciate any pictures, diagrams, and measurements to share with others).
Loading and unloading the casket is easier with more honor guard members at key places. Your specific procedures should be written and practiced at least once a quarter to ensure team members have a general idea of the procedures outlined.
The Casket Deck
The solution to our problems identified above is to create a removable casket deck that can fit into the hose bed that can also double for training. Here is how I created and installed the deck that I use.
I began with a higher quality plywood board that one of the members of Home Depot suggested. It has a nice wood for the outside layer. I then ordered the deck materials required for holding a casket:
- Bier Pin (has a twist knob)
- Bier Pin Plate (7 holes)
- Bier Pin Stop (at rear of deck)
- Bier Pin Stop Plate (1 -or 2-hole)
- Glide Strips (a less expensive alternative to rollers, works extremely well)
I purchased all of my materials from the G. Burns Corporation, they have everything you need and are great at solving any problems one may encounter.
After using the glide strips now for a little while I have encountered one issue that I’ll call “Casket Play”. Casket Play is when you insert the casket, not so much when you remove it. Upon inserting a casket into a coach (the name used for the hearse around the family), the rollers will “grab” the casket and make it quite easy to load straight. The glide strips, however, tend to let the casket slide to either side while the casket is pushed onto the deck, especially if the ground on which the trailer rests is slanted to either side. If you want to completely avoid this, you can purchase rollers from this website and elsewhere.
I drilled and cut the holes after making the necessary marks, it was really quite easy. For the two bier pin plates I considered drilling each hole, but decided to drill each end for the plate and then cut a groove so that I could use each plate hole is necessary.
The stained end was a test for me- which a later regretted while I was staining the rest of the board, it didn’t blend. However, it wasn’t meant to be a family heirloom. At this step is probably where you, for adaptation onto the hose bed, would add a frame with supports running across every couple of feet underneath so that the bolts would not touch the bed.
Then came the stain (Minwax Read Oak), and the protective coats of polyurathane on both sides.
The next step was attaching the materials to the deck. Notice in this picture how the bier pin plates and glide strips are offset to the left, that is to make room in my trailer for the doorway so that the casket can easily slide in and out during training.
My frame was waiting for me in my trainer having built that out of furring strips.
Then came time to install the deck.
To ensure that the casket would not move at all, I cut small squares out of each side of the deck and installed large eye bolts into the frame. With these eye bolts, I use a cargo strap that I crank down to keep the casket safely in place. You can see one of the eye bolts below.
The project finished. My deck is 8’4″ by 3’1″.
I hope you find this helpful.